Posted on

Black Friday Sales!

BLACK FRIDAY SALES SCHEDULE

Sitewide we are having a 10 percent off sale, when  you go to checkout, use the code turkeycoma – any current sales will still be active and your discount will be off your CART total, not off one specific product or category. (shipping is obviously not part of your cart total, nor are applicable taxes for TN residents)

 

Solowerks is offering a MAIL IN rebate on top of our discount, starting the 21st of November through the month of December (our discount sale only goes until the 1st of DEC, if you want the discount and the rebate you need to order before our sale ends) Once you purchase and receive your coilovers, print your receipt and mail it in with a form included in your shipping box to Solowerks and they will cut you a check for 50.00 (25 on caddy kits)

 

 

Malone Tuning is offering 10 percent off all tunes during our promotion!

 

Tower shifters and cables are included in this sale!! Powdercoating will take a few extra days with the holidays so keep that in mind!

 

Check out the products! 

 

Posted on

Install Videos !!

We have needed to do this since the first day we said, “Why don’t we ship out parts for everyone to put a tdi into their mk1” …

 

Well almost 10 years later, and we have a good start on a video library for using and installing our parts..

This is an opening video where we cover alot of 4cyl parts, we will be making several more videos for all of our parts.

 

06a 02a 02j Parts overview :

 

Hydro Clutch Kit

 

Mk1 DBW Pedal Install

 

 

 

Posted on

1980 Caddy TDI Swap

We are building a tdi swap for a customer, he sent us his 1980 caddy, an ALH out of a 00 beetle, and instruction to make it a functional truck, and a great daily driver.

 

  • Alh TDI swap
  • New brakes with rear disc
  • Working Ac
  • New heater system
  • 020 trans w/LSD

 

Onto the evidence :

Getting the truck and motor ready for a steam cleaning, 250 degree pressure washer will cut right through the old grease.

 

Prepping the motor for mk1 install:

  • Remove power steering, trim bracket off
  • Clock Turbo oulet
  • Remove Egr
  • Remove small idler

 

Trimming the cover for the motor mount:

  • Cut along the ridge of the timing cover, then straight down through the relief for the lower roller bearing
  • reinstall and check the fit with the S&P Mk1 – Mk4 bracket

 

  • Clock the turbo by removing the bracket and VNT vacuum pod from the exhaust side,
  • Then loosen the 6 bolts on the charge side and rotate the housing so that it is pointed up instead of down.

 

We installed our 020 clutch kit, the transmission, hung the rebuilt alternator and the new starter.  Waiting on the intake cleaning,  and we are almost ready to set a motor in the car.

 

Motor is IN!

 

 

 

Last thing to do is get the pedal mounted for the DBW ALH ecu..

 

For this to fit the way you want, you will need to trim the floor vent on the factory airbox.. its hard to see in a picture but once you hold the pedal up there you will see exactly what we mean.

Truck is outside for final fluid checks and setting the timing on the pump, hopefully we will have some driving videos from the owner soon!

Posted on

VR-lequin

S&P’s take on a VR6 Harlequin.

Almost everyone has seen one, whether or not they knew it was a purpose built car and not an accident, who knows…

In 1996 Volkswagen built a small batch of cars for a promotional purpose. They were built on a 4 door Golf GL chassis, the only real interior difference was the seat upholstery, it was the same fabric used in the “joker” trim on European models of the same era.  The outside is where the “magic” happened, VW took panels from 4 base color cars (Red, Blue, Green and Yellow) and swapped the removable panels between the other base color cars, leaving you with a very loud exterior.

 

Fast forward to 2015, and I have an opportunity to buy a very sad, yellow base harlequin locally.  It had been resprayed at some point to be all yellow, but the colored panels were peeking through the worn paint.  The driveline was tired, the interior was beyond tired, it was time for either a restoration, or euthanasia…

I sent the car off in pieces to my local painter, he began smoothing out life’s abuses and owners neglect, fixing shopping cart dings, and poorly placed jack stands.  We needed a new hatch, or at least a tub that wouldn’t fall out every time you closed the hatch or went over a bump.

I found someone parting a 4 door golf, that had a lot of Euro market parts, hatch, bumpers, core supports, rebars, etc.  We took it all.

Next on the list was the interior, after looking and not finding anyone wanting to sell their limited edition seats, I spoke with Kip at Loves Trim Shop and worked out a plan for some new threads.  Mk2 Recaros on mk3 bases, leather wrapped, suede inlays and stitching to match the colors outside, without making the interior too loud to enjoy driving it.

That left me to get started on the driveline, the stock ABA was no different in the harlequin cars than it was in a standard Golf GL.

I had a 2.8 24v from a GTI that was wrecked, I had the machine shop go through the block, hone and a ring job, new bearings, new chains, guides, gaskets etc.

I couldn’t help myself, since I had it all in pieces I painted each section of the motor in the matching colors of the car, engine block, head, upper timing cover, lower timing cover, valve cover, intake, accessories, brackets…
I was seeing spots from all of the painting and planning.

Now that the car had been painted back to its original colors, engine painted and assembled and interior back from Love’s, it was time to make it a whole car again.
This is always the fun part, assembly is very gratifying.

Since the interior itself wasn’t very “loud”, Brandon Rosensteel at EuroGlow made an overlay for me.

Once the car was fully assembled, we could enjoy the best part of a vr6 swap – DRIVING!

During this build, a lady had contacted me about wanting to purchase the car when it was done. That is another story all together and arguably better than the one I just told you.
She and “Polly” now are in the Knoxville area, so if you see them, say hello!

Posted on

Matts 1981 VRirocco

Matt wanted to be able to jump in his Scirocco and drive it everyday, without worrying about the failing CIS system leaving him on the side of the road.   To overhaul the 1.8 and rebuild the CIS system was a realistic option, however after looking at the cost of the rebuild he realized he was well on his way to a later model motor swap.  Even better.  Better mileage from an 02 controlled fuel system, more power, easier to find parts. Win-win!

On to the evidence!!

IMG_5176 IMG_5177

Slightly better after a washing!

IMG_5178 IMG_5179

Ready to Paint!

IMG_5184 IMG_5189

Our  MK1 VR6 motor mounts ready to go!

IMG_5181 IMG_5180IMG_5182

Motor hanging!

IMG_5201IMG_5202

Integrated Cable Boss on our mk1 02a mounts, we also offer a smooth version for our mk1 hydro kit

IMG_5211

 

Its ready to go home!

Mk1 Vr6 Scirocco conversion, stainless shift rod kit, full 2.5″ stainless exhaust, silicone coolant lines, hidden 3″ maf intake pipe, 2.25″ tucked radiator with fan and shroud.  everything you need to have a fun in your mk1!

 

Interested in installing one into your own mk1? Interested in having us install one into your mk1?

Check the kit out here !!  Contact us anytime :  info@s-pautomotive.com

 

 

Posted on

1.8t Powered Go-Kart

Steve built this man sized go-kart based off an Ariel Atom, all hand built, no kits or rolling chassis.  He dropped it off for a tidy up on the wiring and to add a couple other items.

 

aa4 aa10

We took a quick note of what needed to be done:

aa2 aa8  aa9

We got to work straight away  cleaning and removing excess wiring and general mess

aa6aa5

Now to start the rebuilding:

aa3 AA1

Concealed under the dash is one of our sealed fuse-boxes we use for large load motor swaps, or in this case, a complete car system:

IMG_5036

 

We also installed a battery disconnect switch, push button start system, a working obd2 port for diagnostics and live data logging.

 

Interested in a project like this? Send us an email, we would love to talk with you about your crazy idea, and how we can help you make it happen, Steve built this car when everyone said he couldn’t, wouldn’t or shouldn’t. That sounds to me like perfect kind of motivation!

Posted on

S&P Radiator and Intercooler Stack

We shortened up our dual pass radiator, and made it stockier, 2.5″ thick core, so that we could put a 21×2.5×3″ intercooler core on the top of it.  Now we can add a condenser to the front if we need to, or tuck it all the way under the core support and make some room for that 1.8t log manifold.

We should have this ready for shipment by mid to late February, we are sorting out the last bits of attachment points, testing outlet sizes and making piping kits for 1.8t and TDIs

 

IMG_4771 IMG_4770 IMG_4767

 

Keep your eye out for a purchase date!

Posted on

EuroTripper 5 Come See Us In Sunny Florida!!

When Eurotripper comes around in the calendar I am ready to find some warmer weather, tired of the wet and cold, GIVE ME SUN and 70 degrees already!!

So come see us at ET5, we will have stuff to fill your grab bag, parts for your project, and an empty chair if you just want to shoot the breeze.

 

et5

 

Get your event details here ET5Show

Posted on

PowerFlex Poly Is Here!

Thats right, ditch the factory rubber for high density poly..

 

We have common kits bundled together, but all of the items are available individually, Control Arms, Steering Racks, Rear Beams, Strut Mounts, Sway Bars Ect…

 

For a limited time get FREE SHIPPING on all of our PowerFlex Parts!!

 

Mk1                                Mk2                                          Mk3                                      Mk4

mk1kit mk2kit

 

mk4frontstrutlowering

Posted on

SHAWWTYS ARE HERE!!

Look at that, a radiator that fits UNDER your core support, now you can tuck it out of your way.  Great for CARBS, ITBS, or even the big VR6 swaps..  We have a special shroud for these radiators, and as with our other radiators, they use the stock fan switch, and factory size coolant inlet and outlets.

Grab just the radiator HERE

 

Grab a shroud package HERE

img_4550 img_4549 img_4544 img_4545 img_4546 img_4547 img_4548