Posted on

Mk1 02a 02j Mk3 and MK4 Motor Swap Info

I made a couple hardware overviews for our trans mounts, and engine swap kits, and I still have a few questions that I either didn’t address in one video or a tip I forgot, I am going to add a couple more videos soon, but this may make finding the info you’re looking for a little easier, if you have questions before during or after install please feel free to email me! Sal@s-pautomotive.com

 

General install Tips:

  • Press your bushings in before you mount the brackets onto the motor or chassis
  • If you have an 02j trans the upper trans mount holes are threaded, you need to drill them out to use the hardware provided
  • Grease the inner speedo cable with a silicone grease before installing!
  • I find it easier to set the radiator in the core support before I install the motor – but not bolt it down
  • For a cleaner install on a motor if you’re not using the AC/PS systems, (external WP motors ABA, HU, AEB cant be cut as much due to the waterpump) cut the bracket off just below the alternator mounting points to the block. (ALHs you will cut the PS off the top)
  • Always start all the bolts in a bracket, manifold,cover etc before tightening any of them down
  • If you are using the mk1 fuel lines, the best place to cut them I have found is just before the cross behind the steering knuckle, you can carefully hand bend them up toward the passenger strut tower and trim again to your desired length
  • Work the exhaust system from front to back, hang everything loose in the clamps and work each section into final placement front to back as well
  • If you’re using one of our harnesses the “Trigger” needs to have power in both the key positions START and RUN – this is often the problem for a no start, someone didn’t check that the wire they chose had power during the crank key cycle. A good source for this is your former coil power wire on gasoline cars, on diesels the injection pump power wire works well.

 

Posted on

Mk1 Vr6 Hardware Videos and Install Tips

I made a couple hardware overviews for our MK1 Vr6 kits, and I still have a few questions that I either didn’t address in one video or a tip I forgot, I am going to add a couple more videos soon, but this may make finding the info you’re looking for a little easier, if you have questions before during or after install please feel free to email me! Sal@s-pautomotive.com

 

General install Tips:

  • Press your bushings in before you mount the brackets onto the motor or chassis
  • If you have an 02j trans the upper trans mount holes are threaded, you need to drill them out to use the hardware provided
  • Grease the inner speedo cable with a silicone grease before installing!
  • I find it easier to set the radiator in the core support before I install the motor – but not bolt it down
  • For a cleaner install on a AAA motor if you’re not using the AC/PS systems cut the bracket off just below the alternator mounting points to the block.
  • Always start all the bolts in a bracket, manifold,cover etc before tightening any of them down
  • If you are using the mk1 fuel lines, the best place to cut them I have found is just before the cross behind the steering knuckle, you can carefully hand bend them up toward the passenger strut tower and trim again to your desired length
  • Work the exhaust system from front to back, hang everything loose in the clamps and work each section into final placement front to back as well
  • If you’re using one of our harnesses the “Trigger” needs to have power in both the key positions START and RUN – this is often the problem for a no start, someone didn’t check that the wire they chose had power during the crank key cycle. A good source for this is your former coil power wire on gasoline cars, on diesels the injection pump power wire works well.

 

 

Posted on

Davids 81 Scirocco

David called and said his 16v was making some “extra” noise, which he believed to be a rod bearing that took an unscheduled leave of absence..  David is from the great white north and had the car shipped down to us to look it over and try to come up with a game plan for his best options moving forward.  We weighed rebuilding the 16v, adding modern fuel management, even forced induction.  After several conversations about options he actually decided that a VR6 would be a nice mid ground to having a NA car, with modern injection control, and a fun to drive powerband.

So I got to work:

Ok, so I had to take advantage of the fact there were 3 red roccos here at the same time..

Now I really got to work…

With the old 16v out, the bay had a few issues from previous owners, while I do not sell myself as a paint and body shop, I will make repairs and spray an engine bay for a customer.

Back side of the repairs seam sealed and ready for service.
With the holes fixed, the bay was ready to paint.

A new coat of paint goes a long way in an old engine bay.

Onto getting the new driveline ready, I had an 04 touareg motor with under 80k on it.  With a touareg motor into a tranverse chassis there are a few pieces you need to swap from either a 2.8 BDF or mk4 r32 motor.  Oil filter housing, oil pump and pan,  exhaust manifolds, accessory bracket (if you want to keep AC, otherwise you can use the treg bracket and accessories) lower timing cover needs to be ground down to clear the trans.

As a rule I always replace service or wear items on a motor before I install it,  so this motor got chains, guides, rear main seal, plugs, coil packs, waterpump, water transfer pipe, thermostat housing, thermostat, valve cover and manifold gaskets.

With all of that done, I was ready to fit the motor.

As you can see the radiator is in before I fit the motor, I cover this in our install videos but this gets overlooked more often than I’d like to hear about.   I am using one of the S&P Mk1 Vr6 radiators with a single fan and a 70c fan switch.

David insisted that we find an Audi intake manifold to dress the motor up a bit over the boring Touareg manifold,  good call on his part, looks great on top of the VR lump.

I knocked out a hidden MAF intake, a remote fill bottle for the coolant system which finished off the plumbing to the radiator and heater core.  These along with the valve cover and upper strut brace got a wrinkle black powder coated finish from TopNotchCustoms located here in town.

Onto wiring,  as with many of these cars the wiring had been touched by alot of people, and they all left their mark..

I removed a lot of the old management wiring, some was even left from the 81 motor that was long gone,  there were abandon relays, multiple wire taps for radios or accessories at some point.  All of it needed to go and start with just what was needed for the current setup in the car.

With the interior wiring in a better place, I moved onto the battery which was moved to the back, using an S&P Battery Box I mounted the Optima Red Top into place with a main breaker mounted on the box itself, this prevents having a 2ga torch running the length of the car if you have a short between the battery and the fusebox/starter/alternator junction point.

The original headlights were tired, I installed some LED low beams and h4 high beams with a pair of Hella relays to keep the load off the switch, this also gave me time to put the face back on the ‘rocco.

Time to get under the car and install the exhaust system. Using a 2.5″ stainless kit from TT with a Borla muffler gets the VR notes out in the perfect way without getting that drone while cruising the highway.

Onto suspension brakes and bearings, I installed a set of Mk1 Solowerks Coilovers  along with new bearings into the ‘rocco spindles, the car was already setup for 10.1″ 16v brakes so just a hardware refresh was needed there.

The seatbelt retracts were sticky, and unresponsive so we sent them out to Safety Restore and had them install some red belts for a bit of color on the inside, David once again was right, it looks great without being LOUD.

With all the safety issues covered it was ready for some road tests.

With all the safety issues covered it was ready for some road tests.

Exhaust Video

Driving Video

I was able to take it to a local show before it had to be loaded up and head home to the Great White North.

This has been one of my personal favorites, its not overstated, its not slammed beyond function, its a ton of fun to drive (yes even in the corners thanks to sway bars and reasonable ride height), it sounds great, it looks good enough to be brought to any GTG or show, but doesn’t have brand new don’t touch me with anything but a diaper paint.  Overall a well sorted car, I hope David gets many years of enjoyment out of it.

Parts available from S&P

Mk1 Vr6 Hardware Kit – Base

Cable Clutch Kit 

S&P Radiator – Vr6 Mk1

Vr6 AAA Based coolant hoses

Tach Adapter

Speedo Cable

Mk1 SS Exhaust

MK1 Vr6 24v downpipe

Solowerks Coilovers

Wiring Services

S&P Battery Box

LUK clutch kit

Posted on

Bruce’s Black 84 GTI

 

Bruce wasn’t a euro guy, that was until he happened across an 84 GTI that needed some love.  Unfortunately some shady people took advantage of Bruce’s good nature and after starting on a 1.8t swap, his car sat and alot of the parts were “missing” .

He brought it to me and after assessing the missing parts, and the general state of the car he decided that he would rather start over with a different driveline and settled on a 12v VR6 that I serviced up with new chains, guides, ignition wires, plugs, new gaskets, fresh clutch and then bolted the S&P Vr6 hardware kit to the VR lump and set it into the mk1 shell.

The car also got a fresh set of 9.4″ gti brakes, a full set of Solowerks Mk1 coilovers and strut mounts.  We cleaned up some chassis wiring issues and sent it home with Bruce, he says he enjoys the look on mustang drivers faces when they cant shake the little mk1 econobox..

A few pics of the install below..

 

S&P Parts Used On The MK1 VR6 Build

MK1 VR6 Bolt in Conversion Kit

Mk1 VR6 Radiator

SoloWerks Mk1 Coilovers

Mk1 Mk2 MK3 VR6 Hidden MAF Intake Pipe and Filter

VR6 Flywheel and Clutch Kits Stock to Stage 4

Mk1 12v Vr6 Downpipe

Mk1 Mk2 02A 02J CABLE CLUTCH CONVERSION Kit

MK1 SHIFT LINKAGE KIT

Posted on

Install Videos !!

We have needed to do this since the first day we said, “Why don’t we ship out parts for everyone to put a tdi into their mk1” …

 

Well almost 10 years later, and we have a good start on a video library for using and installing our parts..

 

4cly Motor/Trans Parts Overview :

 

 

Hydro Clutch Kit

 

Mk1 DBW Pedal Install

 

Mk1 02a/ 02j Linkage Install

 

Mk1 Vr6 Hardware Overview:

 

Mk1 VR6 Harware Install 1&2:

 

 

Wiring Harness Removal Videos –

Mk4

 

Mk3

Posted on

1980 Caddy TDI Swap

We are building a tdi swap for a customer, he sent us his 1980 caddy, an ALH out of a 00 beetle, and instruction to make it a functional truck, and a great daily driver.

 

  • Alh TDI swap
  • New brakes with rear disc
  • Working Ac
  • New heater system
  • 020 trans w/LSD

 

Onto the evidence :

Getting the truck and motor ready for a steam cleaning, 250 degree pressure washer will cut right through the old grease.

 

Prepping the motor for mk1 install:

  • Remove power steering, trim bracket off
  • Clock Turbo oulet
  • Remove Egr
  • Remove small idler

 

Trimming the cover for the motor mount:

  • Cut along the ridge of the timing cover, then straight down through the relief for the lower roller bearing
  • reinstall and check the fit with the S&P Mk1 – Mk4 bracket

 

  • Clock the turbo by removing the bracket and VNT vacuum pod from the exhaust side,
  • Then loosen the 6 bolts on the charge side and rotate the housing so that it is pointed up instead of down.

 

We installed our 020 clutch kit, the transmission, hung the rebuilt alternator and the new starter.  Waiting on the intake cleaning,  and we are almost ready to set a motor in the car.

 

Motor is IN!

 

 

 

Last thing to do is get the pedal mounted for the DBW ALH ecu..

 

For this to fit the way you want, you will need to trim the floor vent on the factory airbox.. its hard to see in a picture but once you hold the pedal up there you will see exactly what we mean.

Truck is outside for final fluid checks and setting the timing on the pump, hopefully we will have some driving videos from the owner soon!

Posted on

Matts 1981 VRirocco

Matt wanted to be able to jump in his Scirocco and drive it everyday, without worrying about the failing CIS system leaving him on the side of the road.   To overhaul the 1.8 and rebuild the CIS system was a realistic option, however after looking at the cost of the rebuild he realized he was well on his way to a later model motor swap.  Even better.  Better mileage from an 02 controlled fuel system, more power, easier to find parts. Win-win!

On to the evidence!!

IMG_5176 IMG_5177

Slightly better after a washing!

IMG_5178 IMG_5179

Ready to Paint!

IMG_5184 IMG_5189

Our  MK1 VR6 motor mounts ready to go!

IMG_5181 IMG_5180IMG_5182

Motor hanging!

IMG_5201IMG_5202

Integrated Cable Boss on our mk1 02a mounts, we also offer a smooth version for our mk1 hydro kit

IMG_5211

 

Its ready to go home!

Mk1 Vr6 Scirocco conversion, stainless shift rod kit, full 2.5″ stainless exhaust, silicone coolant lines, hidden 3″ maf intake pipe, 2.25″ tucked radiator with fan and shroud.  everything you need to have a fun in your mk1!

 

Interested in installing one into your own mk1? Interested in having us install one into your mk1?

Check the kit out here !!  Contact us anytime :  info@s-pautomotive.com

 

 

Posted on

S&P Radiator and Intercooler Stack

We shortened up our dual pass radiator, and made it stockier, 2.5″ thick core, so that we could put a 21×2.5×3″ intercooler core on the top of it.  Now we can add a condenser to the front if we need to, or tuck it all the way under the core support and make some room for that 1.8t log manifold.

We should have this ready for shipment by mid to late February, we are sorting out the last bits of attachment points, testing outlet sizes and making piping kits for 1.8t and TDIs

 

IMG_4771 IMG_4770 IMG_4767

 

Keep your eye out for a purchase date!

Posted on

PowerFlex Poly Is Here!

Thats right, ditch the factory rubber for high density poly..

 

We have common kits bundled together, but all of the items are available individually, Control Arms, Steering Racks, Rear Beams, Strut Mounts, Sway Bars Ect…

 

For a limited time get FREE SHIPPING on all of our PowerFlex Parts!!

 

Mk1                                Mk2                                          Mk3                                      Mk4

mk1kit mk2kit

 

mk4frontstrutlowering

Posted on

SHAWWTYS ARE HERE!!

Look at that, a radiator that fits UNDER your core support, now you can tuck it out of your way.  Great for CARBS, ITBS, or even the big VR6 swaps..  We have a special shroud for these radiators, and as with our other radiators, they use the stock fan switch, and factory size coolant inlet and outlets.

Grab just the radiator HERE

 

Grab a shroud package HERE

img_4550 img_4549 img_4544 img_4545 img_4546 img_4547 img_4548